Padi Fly 50A 60A Brushless 4-in-1 ESC Drone Carbon Fiber Frame Fpv Freestyle Accessories Flying Tower

• Customization: Available
• Weight: 13G
• Installation Hole: 30.5X30.5mm
• Model NO.: PDFLY-FTR003
• Gyroscope: Mpu6500
• Supports Receivers: Elrs/Crsf/Sbus/Ibus Ppm/Spketorum Dsmx, etc
• Bec: 5V3a/9V3a
• Microsd: Card Black Box
• Suitable Models: 5 Inches, 6 Inches, 7 Inches, 8 Inches, 9 Inches,
• Transport Package: Box
• Specification: 36x36mm
• Trademark: PDFLY
• Origin: Shenzhen

Product Description

Padi Fly main business includes UAV detector module, handheld detection, backpack detection, vehicle detection, UAV accessories, etc.
 

Product Description

F405 Flight Controller Stack with 4 in 1 ESC

 

Features:

1. Built with the firm STM32F405 MCU, ICM42688 and large motor pads which makes you can solder up your motors easily and brings a smooth flight experience.

2. Equipped with some pads to support soldering up the LED strip and GPS. After you solder up them, you can fly your model at night and check where is it, which is very convenience.

3. The continuous current of 60A 4 in 1 ESC is 60A*4, the the burst current is 65A for 10 seconds. Support Dshot300, 600 PWM control signal.

4. The mounting size is 30.5 x 30.5mm and the hole diameter is 4mm, which is suitable for most models in the market. You can according to it choose whether it is fit your models or not.

5. Built-in type-c socket, you can connect the flight controller stack with your computer to change the data that you want. The firmware is Betaflight Configurator and INAV.
 

F405 Flight Controller Stack:

MCU	STM32F405
ICM	ICM42688
USB Port Type	Type-C
Barometer	BMP280
OSD Chip	BetaFlight OSD w/ AT7456E chip
DJI Air Unit Connection Way	Two ways supported: 6-pin connector or direct
6-pin DJI Plug	Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Black box	16M Black Box
Current Sensor Input	Supported. For 60A ESC,  please set scale = 180 and Offset = 0.
Power Input	3S - 6S Lipo(Through ESC 8-PIN connector)
5V BEC Output	5 grous 5V output,the total current load is 3A
9V Output	3 groups 9V output,the total current load is 2.5A
3.3V Output	1 group 3.3V output,maxmum current is 300mA
ESC Signal	M1 - M4
UART	6 sets(UART2 UART5, UART3), UART6(Dedicated for SBUS), UART4(Dedicated for ESC telemetry), UART1 (Dedicated for VTX data setting)
Sbs	Debugging to UART6 Channel
ESC Telemetry	UART R4(UART4)
I2C	Supported. SDA & SCL pads on front side. Used for magnetometer.
LED Pad	Supported. LED,5V, and GND pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer	supported,5V,BZ pads for 5V Buzzer
BOOT Button	Supported.
	Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
	When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
Supported Flight Controller Firmware	BetaFlight(Default),
Firmware Target Name	STM32F405
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	37(L) x 37(W) x 6.6(H)mm
Weight	7.5g

BLS 60A 4-in-1 ESC:

Firmware	BLS 16.7
size	41 * 39 * 5mm
Continuous Current	60A * 4
Burst Current	70A(10seconds)
TVS Protective diode	Yes
External Capacitor
ESC Protocol	DSHOT300/600
Power Input	3-6S LiPo
Power Output	VBAT
Current Sensor	35V1000uF Low ESR Capacitor(In the package)Support (Scale=180 Offset=0)
ESC Telemetry	Not supported
Mounting	30.5 x 30.5mm( 4mm hole diameter)
Dimension	42.3(L) * 37(W) * 6.2mm(H)
Weight	12g

 

BLS 50A 4-in-1 ESC:

Product Name
size	41*39*5mm
Aperture	30.5 * 30.5mm
Firmware	BLHELI-S J_H_30_REV16_7
Weight	15g
Continuous current	50A
Maximum current	60A (10 seconds)
Processor	EF8BB21
Drive signal support	DShot150-300-600/Multishot/Oneshot/PMW
Current sensor	supports

 

Detailed Photos

Company Profile

Padi Fly Technology Co. Ltd specializes in the field of advanced technology.

Our company is located in the vibrantcity of Shenzhen,known as a hub of innovation andtechnology in China.

With over 3000 square meters of plant space, we specialize in the design, development, and distribution of FPV drones along with drone countermeasure solution. 
We are known for our innovation, quality, and commitment to enhancing the user experience.

Our Business Range for FPV drone accessories:
We can provide include: Image transmission, motor, carbon fiber frame, flight control, electrical regulation, antenna, remote control, propeller, charger, etc..
We also provide the industry's professional OEM and ODM technology and services.

Packaging & Shipping

 

FAQ

 

Q:Why choose PDFLY?

A:1. From real factory: cheaper price, better quality, faster delivery.

2. Quality assurance: Ship after successful testing.

3. After-sales: Professional team to solve problems and technical support.

 

Q:How can we guarantee quality?

A:1.Always a pre-production sample before mass production;

2.Always final Inspection before shipment;

3.Professional sales staff will communicate with you to confirm every link

 

Q:What's the lead time?

A:Sample needs 3-7 days, mass production needs 7-10 days, according to your order requirements & volumes.

 

Q:How to place an order from you?

A:Please send the products you like to us and our professional sales will contact with you within 24 hours to confirm the details of the products and negotiate. After you confirm the order, we will guide you through payment and arrange delivery, tell you the tracking number and help track the logistics.

 

We look forward to your comments on our products and services.